Hostname: page-component-54dcc4c588-r5qjk Total loading time: 0 Render date: 2025-10-08T15:38:15.270Z Has data issue: false hasContentIssue false
  • English
  • Français

Metalized Polypropylene Film in Capacitors: Characterization and The Effect of Interfacial Pressure on the Dielectric Strength

Published online by Cambridge University Press:  15 February 2011

Shalabh Tandon  and
Richard J. Farris
Shalabh Tandon
Affiliation:
Silvio O Conte Building, Polymer Science and Engineering Department, University of Massachusetts, Amherst, MA 01003.
Richard J. Farris
Affiliation:
Silvio O Conte Building, Polymer Science and Engineering Department, University of Massachusetts, Amherst, MA 01003.
Get access

Abstract

Metalized polypropylene film used in high energy density capacitors has been mechanically characterized to determine its elastic constants. The out of plane coefficient of thermal expansion (CTE) of the orthotropic film is 10 times as large as the smaller in plane CTE. The out of plane modulus is twice as large compared to one of the in plane moduli. The effect of interfacial pressure on the dielectric breakdown is also studied for the same film. It is observed that the dielectric strength of the film decreases at first and then increases above 4 MPa of compressive stress.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 476: Symposium N – Low-Dielectric Constant Materials III , 1997 , 147
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

REFERENCES

1. Gilleo, K., Polymer Thick Film, (Van Nostrand Reinhold, New York, 1996).Google Scholar
2. Ulrich, H., Introduction to Industrial Polymers, (Hanser Publishers, New York, 1982), p. 53.Google Scholar
3. Sweeting, O., Ed., The Science and Technology of Polymer Films, I, (Interscience Publishers, New York, 1968), p. 11–13.Google Scholar
4. Reed, C.W. and Cichanowski, S.W., IEEE Transactions on Dielectrics and Electrical Insulation, 1, [5], 904, (1994).Google Scholar
5. Hudis, M. and Howe, D., Motor Run Capacitors, Aerovox Group®, Aerovox Inc., New Bedford, MA.Google Scholar
6. Shaw, D.G., Cichanowski, S.W. and Yializis, A., Proceedings of a Symposium on High Energy-Density Capacitors and Dielectric Materials, (National Academy Press, Washington D. C., 13–48, 1981).Google Scholar
7. Ariyama, T., Polymer Engi. And Sci., 33, [22], 1494–1501, (1993).Google Scholar
8. Karger-Kocsis, J. Ed., Structure and Morphology-I, (Chapman and Hall, London, 1995).Google Scholar
9. Sheth, K. C., Stress. Mechanical and Thermal Characterization of Anisotropie Polvimide Thin Films and coatings, Ph.D. Thesis, University of Massachusetts, Amherst, MA, (1996).Google Scholar
10. The 9um thick, metalized polypropylene film was obtained from Aerovox Corporation, New Bedford, MA.Google Scholar
11. Altmann, H.C., Tappi, 51, [4], (1968).Google Scholar
12. Yagoda, H.P., ASME J. of Appl. Mechanics, 47, 847, (1980), (and REFERENCES therein).Google Scholar
13. Reuter, R.C. Jr. and Allen, J.J., Journal of Mechanical Design, 113, 387, (1991).Google Scholar
14. Allen, J.J. and Reuter, R.C. Jr., Journal of Mechanical Design, 113, 393, (1991).Google Scholar
15. Champion, J. V., Dodd, S.J. and Stevens, G.C., J. Phys. D: Applied Phys., 27, 142, (1994).Google Scholar
16. Park, C. H., Kaneko, T., Hara, M. and Akazaki, M., IEEE Transactions on Electrical Insulation, EI–17, [3], 234, (1982).Google Scholar
17. Zebouchi, N., Bendaoud, M., Essolbi, R., Malec, D., Ai, Bui and Giam, H.T., J. Appl. Phys., 79, [5], 2497, (1996).Google Scholar
18. Zebouchi, N.,, Essolbi, R., Malec, D., Giam, H.T., Ai, Bui and Bendaoud, M., J. Appl. Phys., 76, [12], 8218, (1994).Google Scholar
19. Kawamoto, A., Suzuoki, Y., Ikejiri, T., Mizutani, T. and leda, M., IEEE Transactions on Electrical Insulation, 23, [2], 201, (1988).Google Scholar
20. Hudis, M., Aerovox Inc., New Bedford, MA, personal communication.Google Scholar
21. Maden, M. A. and Farris, R. J., Exp. Mech., 31(2), 178 (1991).Google Scholar
22. Tong, Q. K., A Structure Property Investigation of a Multi-Component Polvacrvlate Photoresis, Ph.D. Thesis, University of Massachusetts, Amherst, MA (1993).Google Scholar
23. McCullough, R. L., Micromechanical Materials Modeling, 2, (Technomic Publishing Co., Inc. 1992), Chap. (2.1).Google Scholar
24. Bauer, C. L., The Determination of the Mechanical Behavior of Polvamic Acid/Polvimide Coatings, Ph.D. Thesis, University of Massachusetts, Amherst, MA (1988).Google Scholar
25. Zoller, P., Bolli, P., Pahud, V. and Ackermann, H., Rev. Sei. Instrum., 47(8), 948 (1976).Google Scholar
26. Model 2940 TMA, TA Instruments Inc., New Castle DE 19720; for linear CTE measurements.Google Scholar
27. Gamma High Voltage Research, Ormond Beach, Florida 32174, Model # RR20–3P/PRG10V.Google Scholar
28. Exact Electronics, Hillsboro, OR, USA, Model 340.Google Scholar