Hostname: page-component-54dcc4c588-sdd8f Total loading time: 0 Render date: 2025-10-11T20:39:03.921Z Has data issue: false hasContentIssue false
  • English
  • Français

Electromigration Damage and Failure Distributions in Al-4wt.%Cu Interconnects

Published online by Cambridge University Press:  15 February 2011

W. C. Shih  and
A. L. Greer
W. C. Shih
Affiliation:
University of Cambridge, Department of Materials Science and Metallurgy, Pembroke Street, Cambridge CB2 3QZ, United Kingdom
A. L. Greer
Affiliation:
University of Cambridge, Department of Materials Science and Metallurgy, Pembroke Street, Cambridge CB2 3QZ, United Kingdom
Get access

Abstract

Unpassivated 2.1μm and 1.1μm wide lines of Al-4wt.%Cu have been electromigration-stressed to failure under accelerated testing conditions (up to 300 °C and 2 x 1010 A m-2). The line resistance and microstructure and the development of electromigration damage are discontinuously recorded. Distributions of damage sites (hillocks and voids) along the line lengths are measured, and the evolution of the distributions with stressing time is followed. The distances between damage sites show a clear correlation with the grain structure. Damage and failure sites are concentrated near the end of the lines at which electrons enter.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 391: Symposium T – Materials Reliability in Microelectronics V , 1995 , 391
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

1 Greer, A. L. and Shih, W. C., in Materials Reliability in Microelectronics II. edited by Thompson, C. V. and Lloyd, J. R., (Mater. Res. Soc. Proc. 265, 1992) pp. 83–94.Google Scholar
2 Shih, W. C., Denton, T. C. and Greer, A. L., Materials Reliability in Microelectronics ., pp. 101-106.Google Scholar
3 Shih, W. C., Greer, A. L., Xu, Z. and Jones, B. K., in Materials Reliability in Microelectronics III, edited Rodbell, K. P., Filter, W. F., Frost, H. J. and Ho, P. S., (Mater. Res. Soc. Proc. 309, Pittsburgh, PA, 1991) pp. 369–376.Google Scholar
4 Shih, W. C. and Greer, A. L., J. Electronic Materials, 23 (1994) 1315.Google Scholar
5 Kim, C., Selister, S. I. and Morris, J. W. Jr., in [3], pp. 127-132.Google Scholar
6 Vavra, I. and Lobotka, P., Phys. Stat. Sol. (a) 65, K107 (1981).Google Scholar
7 Shih, W. C. and Greer, A. L., in Thin Films - Stresses and Mechanical Properties V. edited by Baker, S. P., Børgesen, P., Townsend, P. H., Ross, C. A. and Volkert, C. A., (Mater. Res. Soc. Proc. 356, 1995), in press; W. C. Shih and A. L. Greer, in Thin Film Materials and Surface & Interface Structures, eds. L. J. Chen and K.N. Tu, (Inter. Union of Mater. Res. Soc. Proc. of Inter. Conf. on Electronic Materials (IUMRS-ICEM94), 1994), in press.Google Scholar