Hostname: page-component-cb9f654ff-5jtmz Total loading time: 0 Render date: 2025-09-01T10:59:58.911Z Has data issue: false hasContentIssue false
  • English
  • Français

Externally heated cold-seal pressure vessels for use to 1200° C at 1000 bars

Published online by Cambridge University Press:  14 March 2018

D. W. Williams
D. W. Williams*
Affiliation:
Department of Earth Sciences, University of Leeds, Leeds 2
Get access Rights & Permissions [Opens in a new window]

Summary

Apparatus using cold-seal pressure vessels of molybdenum-0·5 %-titanium alloy, where each vessel is protected from oxidation by an argon gas jacket, is described. At 1000 bars pressure these vessels can be used for long runs at temperatures up to 1200° C, an increase of approximately 300° C over the range of conventional Stellite vessels. The possible use of other alloys to extend the range of this type of apparatus further is briefly discussed; pure tungsten has been shown to be too brittle.

Information

Type
Research Article
Information
Mineralogical magazine and journal of the Mineralogical Society , Volume 35 , Issue 275 , September 1966 , pp. 1003 - 1012
Copyright
Copyright © The Mineralogical Society of Great Britain and Ireland 1966

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

Cross, (H. C.) and Simmons, (W. F.), 1954. Alloys and their Properties for Elevated Temperature Service. In Utilisation of Beat Resistant Alloys, Amer. Soc. Metals, Cleveland, Ohio, p. 55.Google Scholar
Luth, (W. C.) and Tuttle, (O. F.), 1963. Amer. Min., vol. 48, p. 1401.Google Scholar
Miller, (G. L.) and Cox, (F. G.), 1961. Development of Oxidation Resistance of some Refractory Metals. In Niobium, Tantalum, Molybdenum and Tungsten (ed. Quarrell, A. G.), Elsevier, Amsterdam, p. 234.Google Scholar
Pentecost, (J. L.), 1963. Coating Materials and Coating Systems. In High-Temperature Inorganic Coatings (ed. Huminik, J. Jr.), Rheinhold Publishing Corporation, New York, p. 10.Google Scholar
Schmidt, (F. F.) and Ogden, (H. R.), 1963. The Engineering Properties of Tungsten and Tungsten Alloys. Report no. 191, Defense Metals Information Center, Columbus, Ohio.Google Scholar
Semchyshen, (M.), 1958. Development and Properties of Arc-Cast Molybdenum-Base Alloys. In The Metal Molybdenum (ed. Harwood, J. J.), Amer. Soc. Metals, Cleveland, Ohio, p. 281. Tem-Pres Research Inc., Information Circular HT-59-2.Google Scholar
Tuttle, (O. F.), 1949. Bull. Geol. Soc. Amer., vol. 60, p. 1727.Google Scholar
Tuttle, (O. F.) and Bowen, (N. L.), 1958. Mem. Geol. Soc. Amer. no. 74.Google Scholar
Weinbexg, (H. P.), 1963. Structural Materials for High-Temperature Use. In High-Temperature Inorganic Coatings (ed. Huminik, J. Jr.), Rheinhold Publishing Corporation, New York, p. ll0.Google Scholar
Yoder, (H. S.), 1950. Trans. Amer. Geophys. Union, vol. 31, p. 827.Google Scholar
Yoder, (H. S.) and Tilley, (C. E.), 1962. Journ. Petrology, vol. 3, p. 342.CrossRefGoogle Scholar